More...
If you want to know how to install a subwoofer, then you need to read the step-by-step guide about the exact procedure. The primary purpose of installing a subwoofer in the cars is they improve the sound of low-frequency to high frequency. The best Subwoofers offer maximum functionality and give their maximum performance with a custom enclosure, speaker driver, and an integrated amplifier. So, when a subwoofer allows so much functionality, then there is a need for installing various devices separately.
For this installing a powered subwoofer in your car is always beneficial. If you have planned to install a subwoofer in your vehicle, or you want to know the correct answer of. Then we are here to help you how to install a powered subwoofer in a car. Our article will provide you with a simple and exact process for the installment of a subwoofer. Now without wasting time, let's get into it.
How to Install a Subwoofer in a Car?
Procedure for the installment of a subwoofer in a car;
- Preparation
- Wiring
- Testing
Preparation:
First of all, open the hood of the vehicle and unplug the negative cable of the battery. Now set it aside. For the placing of the powered subwoofer, estimate the mounting area in the car. Here you have to take care of the space that is not enough for the battery only. But it would be best if you had an amounting place that also allows an adequate amount of ventilation to the integrated amplifiers when it got hot.
It is crucial to pay attention to the mounting area of the battery because it will also determine your subwoofer's performance. For this reason, we will recommend you choose the trunk or cargo area of your car for the mounting of the subwoofer. Now for the wiring hole location, you need to examine the under area of the dash panel. Here you will need a standard size screwdriver and torx bits.
Wiring:
Rout the amplifier cable of the powered subwoofer;
For wiring, you have already found an existing wiring hole. If not, then you can also drill an appropriate size of the hole for the wiring. Moreover, for the accommodation of power, you can also use rubber. Through this hole, you will route the amplifier cable of the powered subwoofer.
Route the power cable towards the battery;
After routing the amplifier power cable through the wiring hole, you will route the battery's power cable. Here make sure the power cable is away from moving mechanical parts and any heated area.
Strip insulation;
Find the connectors that you will get with the amplifier kit. After stripping insulation of ⅜ inch, you will crip these connectors. Now, you need to cut the cable at approximately 1 foot from the rings. Here you will get two newly formed edges, and you will strip insulation at both ends. Now hold both the ends and fuse them with the holder to get with the wiring kit.
Route the power cable towards the mounting area;
Pass the power cable underside the carpet towards the mounting is of the subwoofer. Now, check the rear-mounted power antenna in your car that offers easy access. However, if your vehicle has no antenna that offers easy access for turning on the lead, you need to connect REM. For this, remove the stereo of the dash and connect it to the REM. For the removal of the stereo, you can take help from your car manual.
Connect RCA Cables with a rear head unit;
The next procedure is the connection of the RCA cables with the rear head unit. Once you connect it, reinstall your car stereo. Here, you need to note some points. If your car has original factory stereos, then the subwoofer's installation required high-level signal wiring. Moreover, connect the left and right speakers with the appropriate harness using wire splice taps.
Connection of the switch;
The next step is the connection of the switch lead with the remote turn-on lead. Now mount the subwoofer with the designated area. You can mount with the help of self-tapping secure the subwoofer with the vehicle. The more secured subwoofer, there will be less chance of injury during bumps and collisions.
Installment of negative cable;
For the connection of the negative cable, cut the ground cable. Now install connector rings at the end of both sides of the cables. However, if your subwoofer has a set screw-type power connection, you can install the ring at the end of one edge only.
Connect RCA cable with the subwoofer unit;
Now connect the RCA cable with the subwoofer unit with the help of a remote connection.
Connect the power cable to the battery;
Here the last step of wiring is the connection of the power cable with the battery. For the connection, aside post battery will require an adapter for this connection. On the other hand, a clamp-style battery will connect without the adapter.
Testing:
Checking of wiring connections;
The first step here is checking the wiring connection. After that, reconnect the negative cable of the battery to the negative line.
Turn on the stereo;
Now, turn on the stereo and also adjust the volume to the maximum of subwoofer. Make sure not to touch the audible distortion level.
Adjust gain setting;
Adjust the gain settings with music that has a high dynamic base.
Turn off stereo;
Now, in the last, turn off the stereo and remove any extra interior components. Now the installation process is completed. You can enjoy a higher level of sound quality and a more incredible bass with a power bass subwoofer.
Conclusion:
It feels excellent to install a subwoofer in the car by yourself. A Powered subwoofer installation makes you enjoy a higher bass level and spend your spare time with more enjoyment. However, to enjoy the music, you need to know about how to install a powered subwoofer in a car?
We will recommend you go through the article which will help you to know about how to install a subwoofer and then start the subwoofer's installation process.
